Testing

How to Test a Gyroscope

How to check the gyroscope sensor in your mobile phone, step by step: live readings, a three-axis test and a stability test, and how to tell healthy from faulty.

Published · 3 min read

A good gyroscope test does three things: shows that every axis responds, checks that the readings agree with an independent sensor, and measures how quiet the sensor is at rest. This guide walks through all three.

Before you start

  • Use the phone or tablet you want to test, in an up-to-date browser (Chrome, Safari, Samsung Internet, Firefox or Edge).
  • Remove any case with a magnetic mount, and turn off battery saver or Low Power Mode.
  • Find a firm, flat surface for the stability step.

Step 1: Start live readings

Open the gyroscope test and tap Start test. On iPhone and iPad, tap Allow when Safari asks for motion access. The status should change to Live and the update rate should show a value, typically 50–100 Hz.

Step 2: Understand the axes

The axes belong to the device, not to the room. They turn with the phone:

Axis Runs along Rotating around it looks like
X The short edge, left to right Tipping the top edge toward or away from you (pitch)
Y The long edge, bottom to top Lifting the left or right edge, like turning a page (roll)
Z Straight out of the screen Spinning the phone flat on a table (yaw)

The tester’s Technical details section shows the live reading for each axis.

Step 3: Follow the 3 moves

Tap Test all 3 moves, then copy each move shown by the 3D phone, starting with your phone flat on a table: lift the top, lift the side, and spin it flat. For each move the tester adds up the gyroscope’s rotation rate over time and needs at least 75° of rotation within 30 seconds. It then checks:

  • Response: the target axis reached a clear peak rate.
  • Isolation: most of the motion happened on that axis, which shows the axes aren’t mixed up.
  • Agreement: the gyroscope’s total angle matches the change reported by the separate orientation sensor. Agreement is strong evidence that the readings are real and in the right units.

Step 4: Run the stability test

Tap Start stability test, put the device flat on the table within the 3-second countdown, and don’t touch it for 10 seconds. You get three numbers per axis:

  • Noise SD: how much the readings flicker. Below 0.3 °/s is excellent, below 1 °/s is good, and up to 3 °/s is fair.
  • Mean offset: how far from zero the average reading sits. Ideally under 0.5 °/s, and above 2 °/s can cause drift in apps.
  • Peak: the largest reading seen. If it’s above 8 °/s, the device was moved and the test asks you to repeat it.

Step 5: Save the report

Download report saves a text summary with every number above, plus your browser and sensor-support details. CSV data exports the last 60 seconds of raw readings for a spreadsheet.

How to read the results honestly

A pass on all three axes and a good or excellent stability grade means the gyroscope works as far as a browser can tell. A failed step is a reason to re-test, ideally in another browser, before drawing conclusions. Browsers filter and rate-limit sensor data, so this test can confirm a working gyroscope but can’t diagnose every hardware fault.

  • Troubleshooting4 min read

    Gyroscope Troubleshooting

    Fix phone gyroscope problems on Android and iPhone: no sensor data, blocked motion access, drift, jitter, a dead axis or slow updates. Step-by-step checks.

  • Explainer2 min read

    Gyroscope vs Accelerometer

    Gyroscope vs accelerometer explained: what each phone sensor measures, their units, strengths and weaknesses, and how sensor fusion combines them for orientation.

  • Explainer4 min read

    What Is a Gyroscope?

    Gyroscope definition in plain words: how mechanical and digital MEMS gyroscopes work, what a phone gyroscope sensor measures, and what gyroscope sensitivity means.

Ready to test your gyroscope?

It takes under a minute, works in your browser, and nothing leaves your device.

Start the gyroscope test