Android · Chrome · Samsung Internet

Android Gyroscope Test

Open this page on your Android phone or tablet, tap Start test and move the device. Android browsers usually don’t need a permission prompt, so readings start right away.

Live gyroscope tester

Ready to start

Your phone · live

Test your gyroscope

Tap Start test, then move your device.

Test 1

Test your gyroscope in 3 moves

We’ll show one move at a time. Just copy the picture.

  1. 1Lift the topX axis · Pitch
  2. 2Lift the sideY axis · Roll
  3. 3Spin flatZ axis · Yaw

Tap Start test above first.

Technical details

    Orientation

    angle · degrees
    Pitch
    β · about X
    -°
    Roll
    γ · about Y
    -°
    Yaw
    α · about Z
    -°

    Yaw is measured from where it was when you started, not from compass north.

    Angular velocity

    gyroscope · °/s
    • X Pitch-
    • Y Roll-
    • Z Yaw-
    Update rate
    -Hz
    Jitter
    -ms
    Peak
    -°/s

    Angular velocity · last 10 seconds

    • X
    • Y
    • Z

    Test 2

    Stability test

    Lay the device on a firm, flat surface and don’t touch it. For 10 seconds the tester measures how much the gyroscope readings vary when nothing is moving.

    Results

    Diagnostic summary

    Start the test to see a summary of what your browser and sensor report.

    Readings are processed on your device and nothing is uploaded. Browsers give web pages filtered, rate-limited sensor data, so a missing or odd reading does not prove the hardware is faulty.

    How to test the gyroscope on Android

    1. Open this page in Chrome, Samsung Internet, Edge or Firefox. Use the browser app itself, not a link preview inside a social or messaging app.
    2. Tap Start test. The status should change to Live within a second.
    3. Rotate the phone slowly around each axis and watch the matching X, Y or Z value rise.
    4. Run Test all 3 moves, then the stability test with the phone flat on a table.
    5. Tap Download report to save the results.

    Allowing motion sensors in Chrome

    Chrome on Android allows motion sensors for websites by default, but they can be turned off for all sites or for one site. If the tester shows Permission denied or No sensor data:

    1. Tap the site-settings icon to the left of the address bar, then Permissions, and make sure Motion sensors is allowed.
    2. To check the global setting, open Chrome’s menu ⋮ → Settings → Site settings → Motion sensors, and allow sites to use them.
    3. Reload the page and tap Start test again.

    Samsung Internet and Edge have similar options under their own site-permission settings. Menu names vary between versions.

    What the Android readings mean

    ReadingSourceUnit
    Pitch, roll, yawOrientation (fused gyroscope, accelerometer and sometimes magnetometer)degrees
    X / Y / Z angular velocityGyroscope rotation rate°/s
    Update rateHow often the browser delivers motion eventsHz

    Chrome usually delivers motion data at about 60 Hz, regardless of how fast the hardware sensor runs. A rate of 60 Hz in the tester is a browser limit, not a weak gyroscope.

    Android-specific problems

    • Readings freeze when the screen dims. Browsers pause sensors in background tabs and on a locked screen. The tester pauses and resumes for you.
    • Low or uneven update rate. Battery saver and some vendor power-management modes throttle sensor events. Turn them off for the test.
    • The 3D model drifts when the phone is still. Small drift of the yaw angle is normal on devices without good magnetometer fusion. Tap Re-center.
    • Some budget phones have no gyroscope. On those phones orientation may still work (estimated from the accelerometer and compass), but angular velocity stays unavailable. The tester tells you when that happens.

    For more fixes, see the gyroscope troubleshooting guide.

    Ready to test your gyroscope?

    It takes under a minute, works in your browser, and nothing leaves your device.

    Start the gyroscope test